Home » U++ Library support » Slider&ProgressIndicator » SliderCtrl with UHD
SliderCtrl with UHD [message #45403] |
Mon, 09 November 2015 13:18 ![Go to next message Go to next message](theme/default/images/down.png) |
Tom1
Messages: 1221 Registered: March 2007
|
Senior Contributor |
|
|
Hi,
It looks like the dial on the SliderCtrl does not scale properly on UHD environment.
Best regards,
Tom
|
|
|
|
Re: SliderCtrl with UHD [message #45428 is a reply to message #45413] |
Wed, 11 November 2015 15:12 ![Go to previous message Go to previous message](theme/default/images/up.png) ![Go to next message Go to next message](theme/default/images/down.png) |
Tom1
Messages: 1221 Registered: March 2007
|
Senior Contributor |
|
|
Hi Mirek,
Now the dial is even smaller and more difficult to hit on UHD. However, when I 'catch' the dial to drag, it grows a lot and is of somewhat suitable size until I release the drag again. (The shape has also changed to something like two ended wedge and changes to a single ended wedge when dragged. I think the default old fashioned rectangular dial would be sufficient, unless too much trouble. That one also makes better use of the vertical space of a horizontal slider.)
Best regards,
Tom
|
|
|
|
Re: SliderCtrl with UHD [message #45456 is a reply to message #45440] |
Tue, 17 November 2015 20:56 ![Go to previous message Go to previous message](theme/default/images/up.png) ![Go to next message Go to next message](theme/default/images/down.png) |
Tom1
Messages: 1221 Registered: March 2007
|
Senior Contributor |
|
|
Hi
Thanks Mirek. I'm visiting the home country of U++ and will be back at the office next week. I will test it then.
Best regards,
Tom
|
|
|
Re: SliderCtrl with UHD [message #45485 is a reply to message #45456] |
Mon, 23 November 2015 11:51 ![Go to previous message Go to previous message](theme/default/images/up.png) ![Go to next message Go to next message](theme/default/images/down.png) |
Tom1
Messages: 1221 Registered: March 2007
|
Senior Contributor |
|
|
Hi,
Just tried the Slider at UHD and now the dial looks just right size and shape until I drag it. When pressed, it shrinks to half in width and height, and covers just the top left quarter of the area it should.
Best regards,
Tom
|
|
|
|
Re: SliderCtrl with UHD [message #45497 is a reply to message #45493] |
Tue, 24 November 2015 05:15 ![Go to previous message Go to previous message](theme/default/images/up.png) ![Go to next message Go to next message](theme/default/images/down.png) |
Novo
Messages: 1371 Registered: December 2006
|
Ultimate Contributor |
|
|
mirek wrote on Mon, 23 November 2015 15:36
In related news, UHD mode is now enabled by default (no need to call Ctrl::SetUHDEnabled() anymore).
Thanks a lot!
Regards,
Novo
|
|
|
Re: SliderCtrl with UHD [message #45498 is a reply to message #45493] |
Tue, 24 November 2015 09:10 ![Go to previous message Go to previous message](theme/default/images/up.png) |
Tom1
Messages: 1221 Registered: March 2007
|
Senior Contributor |
|
|
Hi,
Now the SliderCtrl looks and works on UHD just as expected. Thanks!
Also, it was a good decision (at least from my point of view) to enable UHD support by default. Thanks for that too.
Best regards,
Tom
|
|
|
Goto Forum:
Current Time: Sun Sep 01 07:45:49 CEST 2024
Total time taken to generate the page: 0.01047 seconds
|