U++ forum: Welcome to the forum

Search on this site

Search in forums

Home » Community » Newbie corner » MSVC 10 to Upp conversion

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Re: MSVC 10 to Upp conversion [message #32794 is a reply to message #32793]

Fri, 10 June 2011 03:36

nlneilson
Messages: 644
Registered: January 2010
Location: U.S. California. Mojave &...

Contributor

Note that all the GUIs has a label FWTools and an edit field that shows "OK".
This is intended to check that ntile.exe is in FWTools\bin or if the FWTools\bin is linked correctly if the GUI is a stand alone .exe with the ntile included.

The previous GUIs had a wide box to show any errors in the dos box that was on top of only the GUI, maybe putting a pause at the end would keep the whole box visible on error.

http://www.nlneilson.com/wwposts/GUI_1.jpg

[Updated on: Fri, 10 June 2011 07:46]

Report message to a moderator

[Message index]

		MSVC 10 to Upp conversion By: nlneilson on Mon, 30 May 2011 22:22
		Re: MSVC 10 to Upp conversion By: koldo on Mon, 30 May 2011 22:54
		Re: MSVC 10 to Upp conversion By: nlneilson on Mon, 30 May 2011 23:05
		Re: MSVC 10 to Upp conversion By: nlneilson on Tue, 31 May 2011 01:39
		Re: MSVC 10 to Upp conversion By: nlneilson on Tue, 31 May 2011 04:43
		Re: MSVC 10 to Upp conversion By: dolik.rce on Tue, 31 May 2011 08:03
		Re: MSVC 10 to Upp conversion By: koldo on Tue, 31 May 2011 08:40
		Re: MSVC 10 to Upp conversion By: nlneilson on Tue, 31 May 2011 12:29
		Re: MSVC 10 to Upp conversion By: koldo on Tue, 31 May 2011 21:20
		Re: MSVC 10 to Upp conversion By: nlneilson on Tue, 31 May 2011 22:06
		Re: MSVC 10 to Upp conversion By: nlneilson on Wed, 01 June 2011 02:59
		Re: MSVC 10 to Upp conversion By: koldo on Wed, 01 June 2011 08:06
		Re: MSVC 10 to Upp conversion By: nlneilson on Wed, 01 June 2011 08:37
		Re: MSVC 10 to Upp conversion By: nlneilson on Wed, 01 June 2011 10:10
		Re: MSVC 10 to Upp conversion By: nlneilson on Wed, 01 June 2011 11:29
		Re: MSVC 10 to Upp conversion By: koldo on Wed, 01 June 2011 12:09
		Re: MSVC 10 to Upp conversion By: nlneilson on Wed, 01 June 2011 12:35
		Re: MSVC 10 to Upp conversion By: koldo on Wed, 01 June 2011 17:19
		Re: MSVC 10 to Upp conversion By: nlneilson on Wed, 01 June 2011 23:05
		Re: MSVC 10 to Upp conversion By: nlneilson on Thu, 02 June 2011 00:41
		Re: MSVC 10 to Upp conversion By: koldo on Thu, 02 June 2011 08:36
		Re: MSVC 10 to Upp conversion By: nlneilson on Thu, 02 June 2011 11:12
		Re: MSVC 10 to Upp conversion By: koldo on Thu, 02 June 2011 11:37
		Re: MSVC 10 to Upp conversion By: nlneilson on Thu, 02 June 2011 12:21
		Re: MSVC 10 to Upp conversion By: nlneilson on Thu, 02 June 2011 13:15
		Re: MSVC 10 to Upp conversion By: koldo on Thu, 02 June 2011 13:53
		Re: MSVC 10 to Upp conversion By: nlneilson on Fri, 03 June 2011 01:54
		Re: MSVC 10 to Upp conversion By: nlneilson on Fri, 03 June 2011 03:26
		Re: MSVC 10 to Upp conversion By: nlneilson on Sun, 05 June 2011 04:05
		Re: MSVC 10 to Upp conversion By: nlneilson on Sun, 05 June 2011 05:38
		Re: MSVC 10 to Upp conversion By: koldo on Sun, 05 June 2011 06:58
		Re: MSVC 10 to Upp conversion By: nlneilson on Sun, 05 June 2011 10:35
		Re: MSVC 10 to Upp conversion By: nlneilson on Mon, 06 June 2011 23:57
		Re: MSVC 10 to Upp conversion By: koldo on Tue, 07 June 2011 07:17
		Re: MSVC 10 to Upp conversion By: nlneilson on Tue, 07 June 2011 07:45
		Re: MSVC 10 to Upp conversion By: koldo on Tue, 07 June 2011 15:59
		Re: MSVC 10 to Upp conversion By: nlneilson on Thu, 09 June 2011 10:38
		Re: MSVC 10 to Upp conversion By: nlneilson on Thu, 09 June 2011 23:28
		Re: MSVC 10 to Upp conversion By: nlneilson on Fri, 10 June 2011 01:19
		Re: MSVC 10 to Upp conversion By: nlneilson on Fri, 10 June 2011 03:36
		Re: MSVC 10 to Upp conversion By: nlneilson on Fri, 10 June 2011 13:14
		Re: MSVC 10 to Upp conversion By: nlneilson on Sat, 11 June 2011 09:02
		Re: MSVC 10 to Upp conversion By: nlneilson on Mon, 13 June 2011 13:06
		Re: MSVC 10 to Upp conversion By: koldo on Tue, 14 June 2011 09:17
		Re: MSVC 10 to Upp conversion By: nlneilson on Tue, 14 June 2011 10:15

Previous Topic:	Please recommend a scripting language
Next Topic:	String to std::string conversion

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon May 20 05:52:44 CEST 2024

Total time taken to generate the page: 0.00988 seconds